Water & containers
Refresh water and empty/rinse the drip tray and grounds container.
Siemens EQ600 iAroma
EQ600 iAroma maintenance, organised around the jobs that matter.
EQ600 iAroma sits between EQ500 and EQ700 and follows Siemens’ current maintenance logic: prompted service programmes, removable brewing-unit care, milk-system hygiene and water-filter management.
Maintenance schedule
The useful baseline for your EQ600 iAroma.
Use the machine’s own prompt sooner whenever it asks for maintenance. Water hardness and usage can also change the practical timing.
VENTORI CARE · ANDROIDTrack this machine in Ventori Care.
Track this machine in Ventori Care ↗Keep this maintenance schedule, reminders, history and available guides with the machine instead of remembering the next job yourself.
Milk system
Allow automatic milk cleaning to run and clean removable milk-contact parts as required.
Brewing unit
Remove and rinse the brewing unit with warm water; do not use detergent on it.
Cleaning / Calc’nClean
Run the prompted service programme and follow the display sequence.
Water filter
Replace the compatible filter and keep the water-hardness setting accurate.
Personalise this schedule
Want Ventori to remember the Siemens EQ600 iAroma maintenance rhythm for you?
Your machine is already selected. Add local water hardness and typical use without choosing the manufacturer or model again.
Daily hygiene
Keep water, trays and residue under control.
The automatic programmes handle the internal cycle, but daily physical hygiene still matters.
Refresh the water
Use fresh water in the tank and keep the tank itself clean rather than repeatedly topping up old water.
Empty the drip tray and grounds container
Empty and rinse both regularly so moisture and coffee residue do not accumulate inside the machine.
Let automatic rinses finish
Do not interrupt the machine while it is completing a normal rinse or service-programme stage.
Removable brewing unit
Rinse the brewing unit separately.
Unlike JURA, Siemens bean-to-cup machines use a removable brewing unit on these families. Siemens guidance for current machines such as EQ700 is warm water and a gentle brush — no detergent or acid.
Switch off and open the service door
Follow the access sequence for your exact Siemens model before removing the brewing unit.
Remove the brewing unit
Release it using the model-specific latch or handle without forcing the mechanism.
Rinse with warm water
Use warm water and a gentle brush where needed. Do not use washing-up liquid, detergent, vinegar or acid on the brewing unit.
Allow it to drain
Shake off excess water and allow the unit to drain before refitting it.
Reinstall and lock it
Return the unit fully to position and close the service door before switching the machine back on.
Do not put the brewing unit in a dishwasher unless the exact Siemens manual explicitly permits it.
Combined service programme
Cleaning and descaling are separate jobs — Calc’nClean can combine them.
When both are due, supported Siemens machines can offer Calc’nClean. The display controls the order and tells you when to add the cleaning tablet and descaling solution.
Run the programme when prompted
Siemens determines service timing from use, water hardness and machine status. Do not substitute a fixed calendar for the machine prompt.
Clean the brewing unit first
On families such as EQ500, Siemens says the brewing unit should be clean before the Calc’nClean programme is run.
Add the cleaning tablet where instructed
Use the machine’s tablet compartment or grounds compartment at the point requested by the display; never drop a cleaning tablet into the water tank.
Remove the water filter if instructed
The programme can ask for a fitted filter to be removed before the descaling phase.
Prepare the descaling solution
Dissolve the correct descaling dose in the amount of warm water specified by the machine programme.
Complete every rinse stage
Refill with fresh water when instructed and let the entire programme finish before returning to normal use.
Milk-system hygiene
Automatic milk rinsing is helpful, but it is not the whole job.
Milk-equipped Siemens machines use automatic rinsing on many current families, but removable milk-contact components and deeper cleaning still need attention.
Use the automatic milk rinse
Where AutoMilk Clean is fitted, allow the steam-cleaning burst after milk drinks to complete.
Run deeper milk cleaning when requested
Automatic steam rinsing does not replace the machine’s deeper milk-system cleaning routine.
Clean removable milk-contact parts
Rinse and clean the milk hose, container, adapter and outlet parts according to the exact machine instructions.
Water care
Match the filter and hardness setting to the exact Siemens model.
Current Siemens service guidance uses INTENZA filtration across multiple EQ families. The machine’s hardness setting and active filter status affect when descaling is requested.
Check exact filter compatibility
Confirm the model or E-number before ordering a replacement cartridge.
Prepare and install the filter
Follow the cartridge instructions and machine setup flow rather than assuming every EQ generation uses the same activation sequence.
Set or confirm water hardness
The service interval is influenced by hardness, so keep the machine configuration accurate.
Replace when prompted
Use the machine filter message as the primary replacement cue.
MODEL-SPECIFIC CHECK
Siemens product support ↗Use the exact procedure for your machine.
Siemens programme names and control sequences vary by exact E-number. Check the identification plate and use the exact model support page if your controls differ.
Understand the care task
Relevant Ventori care
Match the maintenance product to the job.
Coffee-system cleaning and descaling are separate jobs. Use the correct product at the stage requested by the Siemens service programme.